PracticalBoater

Do-It-Yourself

 

Removing Stubborn Fittings

By Don Casey
Published: June/July 2014

What to do when that fitting doesn't want to let go.

Photo of boat deck fittings
The mysterious sealants that hold fittings to your deck needn't deter you from re-bedding.

What exactly is the rubbery material beneath your pulpit bases, sealing your thru-hulls, or gripping your port lights? What type of goop is holding that fitting to your deck? Maybe you know if you are the one who put it there, but if it came with the boat, or was applied by someone else, you probably don't know. Only when faced with separating component parts will you learn the true nature of the sealant.

Why does this matter? Because some sealants permit easy separation and renewal while others turn de-bedding into a contest of will. If the sealant is a bedding compound (e.g. Dolfinite), acrylic caulk, butyl rubber, silicone, polysulfide (e.g. Life-Calk), or even the more tenacious polyether sealant, separation will normally just be a matter of prying to break the bond or stretch the sealant beyond its elongation capacity. However, if the sealant is polyurethane, particularly the ever popular 3M 5200, any attempt to separate the components by simply prying them apart is likely to end in the damage of one or both of the joined pieces.

So how do you separate parts bonded together with adhesive sealant? Start with step 1 and stop when the fitting comes free. However, if you're trying to remove plastic fittings that you know were bonded with 5200, you'll get less frustrated and do less damage if you skip down to step 6 right now.

1. Extract Mechanical Fasteners

Even this can be a challenge when they were originally installed with a coating of polyurethane. Bolts should be unscrewed. A big screwdriver, perhaps with a wrench on the shank, can normally deliver adequate force. For more torque, try a manual impact driver.

2. Try Separating The Parts By Pulling Or Prying

Continuous pressure will be more effective than hammering and carries a lower risk of damage. It gives elastic sealants time to resolve internal stresses and either elongate or release. If the sealant does neither, it is probably polyurethane. More force is not the solution. Plastic and cast parts will break and machined parts bend. The grip is even strong enough to rip away gelcoat. Time to move on to step 3.

3. Cut The Bond

Photo of a razor knife

You'll need a sharp blade — a razor knife, carpet knife, or single-edge razor blade. If you can reach all sides and the sealant is thick enough, slicing the perimeter weakens the bond. Pry just enough to allow your blade farther into the joint and keep slicing deeper until you cut the components apart. If whatever tool you're using isn't working, try a wire saw, simply a foot-long length of thin wire — leader wire, guitar string, braided fishing line, what-have-you — with rings or dowels at each end that will allow you to saw the wire back and forth between the bonded parts. Wedges or prying behind the wire can assist in sawing completely through the sealant pad.

4. Try Some Stress

If you cannot cut the components apart, try putting the adhesive under moderate stress, then giving it time to elongate or release. For a piece of deck hardware, that might mean driving a couple of chisels or other wedges under one edge sufficient to deflect but not bend the base, then leaving them for a day or more. As separation allows, tap the wedges deeper.

5. Heat Things Up ... Carefully

Where both bonded surfaces are metal, a heat gun or torch can melt the adhesive and break its grip. However, if your boat is fiberglass, the use of heat risks permanent damage because the temperature required to soften cured polyurethane will also soften cured polyester. Only heat the blade of your knife, razor, or wire, which can help it to penetrate the cured sealant more easily.

6. Chemical Reaction

The list of solvents tried by desperate boat owners is exhaustive: acetone, toluene, xylene, MEK, alcohol, gasoline, WD-40, citrus cleaners, and more. Most have no effect on cured polyurethane and none work well enough to recommend. One chemical product that does get high marks is DeBond Marine Formula. More liquid knife than solvent, it is sprayed onto the exposed sealant after the edges have been scored with a blade. Employing wedges to keep the sealant under stress exposes a fresh target to the chemical as the bonded edge moves back with release. Given time and repeat applications, it's usually successful at breaking the bond of 3M 5200 (and other adhesive sealants as well).

Unlike some other release chemicals — there are several on the market — the DeBond product is also compatible with most plastics, except polycarbonate (Lexan). Without the use of a bond releaser, plastic parts — port light frames, for example — installed with 3M 5200 or other high-strength adhesive typically cannot be dismantled without damage. There is no downside to using a release chemical, beyond expense, so going to it first rather than last can pay dividends.

Here is a takeaway about polyurethane: The bond is permanent but the seal
isn't. That means things may still be stuck together just fine, but they will
still be leaking. If you don't want to do this again, re-bed with a less adhesive sealant.End of story marker

 

Don Casey is the author of the classic This Old Boat, which covers all aspects of refurbishing an older fiberglass sailboat.

 

 Recommended Articles
Gray rule

Thumbnail photo of boat sealantsBoat Sealants

Perfect technique can't make up for the wrong sealant. If you want to stop that leak, start by getting the sealant right


Illustration of cleaning all the sealant off the cleatInstall Boat Deck Fittings

If you're re-bedding, hopefully the old sealant is one that will allow you to separate the joint without difficulty or damage


Thumbnail photo of tapping with a hammerRemoving Stripped Or Frozen Bolts And Screws

Frozen bolts driving you crazy? Here's some tips on how to remove them

 


Remove Thru-Hull Fittings

Thu-hull fitting illustration

Thru-hull fittings can be jacked free with a length of threaded rod, a stiff backing plate, and three scraps of 2x4. Drill a hole through the center of the backing plate and the center of one of the wood scraps. Pass the threaded rod through the wood, up through the thru-hull fitting and, inside the boat, through the backing plate. Add a washer and thread on a nut inside, then seat the plate on the inside end of the fitting. Outside create a bridge by using the other two pieces of wood to support the ends of the speared piece on either side of the fitting. Add a washer and a nut, tightening until the bridge is clamped in place. Now turning the nut will pull the backing plate toward the hull, extracting the thru-hull in the process. Putting the sealant under stress then giving it time to stretch can avoid the common result of tearing away bits of the fiberglass laminate. If the sealant is polyurethane, a release chemical can help.

 

BoatUS Magazine Is A Benefit Of BoatUS Membership

Membership Also Provides:

  • Subscription to the print version of BoatUS Magazine
  • 4% back on purchases from West Marine stores or online at WestMarine.com
  • Discounts on fuel, transient slips, repairs and more at over 1,000 businesses
  • Deals on cruises, charters, car rentals, hotel stays and much more ...
  • All For Only $24 A Year!


Join Today!