] ]

 
] ] ]
]
Welcome Guest ]
]
] ]

] ] ]
]
Site Navigation ]
]
] ]

] ] ]
]
Top 10 Recent Posts ]
View Last Post Murray Chris Craft Constellations
Pages 1 2 3 4 ... 149 » 150
Last Post By: Capt Jim
Forum: Chris Craft

Posted: August 29 2014 at: 11:06

View Last Post 1991 Four Winns 365
Last Post By: Blue Moon 138
Forum: Four Winns

Posted: July 16 2014 at: 17:35

View Last Post Seat Cushions
Last Post By: Michael Acord
Forum: Sea Fox

Posted: June 06 2014 at: 16:02

View Last Post Sail cleanin’ and hull patchin’
Last Post By: dad21dawg
Forum: Hunter

Posted: May 29 2014 at: 16:01

View Last Post 1983 25’ Chris Craft Catalina
Last Post By: fred6963
Forum: Chris Craft

Posted: May 27 2014 at: 14:26

View Last Post 1963 Constellation 42
Last Post By: spellbound
Forum: Chris Craft

Posted: May 06 2014 at: 08:31

View Last Post Viking Yachts Links
Last Post By: Viking44
Forum: Viking Yacht

Posted: April 17 2014 at: 06:32

View Last Post Amerosport 320
Last Post By: Jerry737
Forum: Chris Craft

Posted: April 13 2014 at: 16:00

View Last Post Any Uniflite Owners near Berkeley CA???
Last Post By: concordian
Forum: Uniflite

Posted: March 08 2014 at: 02:27

View Last Post Inverter
Last Post By: eshover
Forum: Chris Craft

Posted: February 03 2014 at: 11:32

]
] ]
   
Carver
 BoatUS Boat Groups/Manufacturer Forums>>Carver
Subject Topic: Water Temp Guage Post ReplyPost New Topic
 
] ] ]
]
Author
Message Prev Topic | Next Topic 
bobmay50
"Seaman Recruit"




Joined: September 12 2006
Posts: 1
Posted: September 24 2007 at 17:41 | IP Logged Quote bobmay50

We have a 1989 36 Aft Cabin Carver with Merc engines.  One of our water temp guages is not working.  We've replaced the guage, installed all new wiring on both the bridge and lower station guages.  We've installed a new iginition switch and have even checked the guages off the other motor and found them to read the water temp in that motor.

I'm looking for a solution.  I'm thinking that the sensor may be bad...although I was told a new one was installed.  Ideas?  Thanks...my temperature is rising over this problem.  Mo Bo'T Lake of the Ozarks.



__________________
Bob and Mo of Mo Bo'T
Back to Top Printable version View bobmay50's Profile Search for other posts by bobmay50
 
gbarger
"Seaman Recruit"




Joined: March 30 2000
Posts: 29
Posted: September 24 2007 at 19:39 | IP Logged Quote gbarger

If you proved that the new guage works off the other motor by switching the wires at the sensor, then you have also proved that the sensor is bad.

If you switched the wires at the helm station, then it could be the sensor or the wiring.

To prove it is the sensor, just switch the sensors around.  I have purchased defective new parts, so yes the "new" sensor could be bad.

 

Of course if you have a multi meter, just check the ohms resistance across the sensor as the temp rises.

Gary

 



Edited by gbarger on September 24 2007 at 19:40
Back to Top Printable version View gbarger's Profile Search for other posts by gbarger
 
]
] ]
 

If you wish to post a reply to this topic you must first login
If you are not already registered you must first register

  Post ReplyPost New Topic

] ] ]
]
  ]
Printable version Printable version
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum
]
] ]

] ] ]
]
©2014, Boat Owners Association of The United States. All Rights Reserved.
This page was generated in 0.7813 seconds.
]
] ]