Trailering


12 Steps To Repacking Or Replacing Your Bearings

By Patrick Piper

It's a job you tackle yourself or one best left to a professional. If you choose the first option, here's what to do.

Exploded view of trailer bearing assembly

Statistics from BoatUS TRAILER ASSIST files show that almost one out of every four calls from Trailering Club Members with a trailer broken down along the side of the road is about bearings gone bad. Some boat trailers use a more modern oil-bath hub design for bearings, but most use grease, which is why we're spending some time with BoatUS service provider Chris Grimm of www.LegendaryTrailers.com.  Steps to take may vary with different products or situations, but this gives you a general idea.

Here Are The Items You'll Need For The Job:

  • A jack and a stand
  • Boat-trailer bearing kit with the proper size bearings, races, and a double lip grease seal.
    NOTE: Bearing kits are usually one of five sizes: 3/4", 1", 1 3/8", 11/4", 11/16". If unsure, each bearing and race has a stamped part number
  • Bearing Grease — Don't mix different brands
  • A large flat screwdriver, needle-nose pliers, a lug wrench or channel locks.
  • A hammer and a soft hammer (made with brass and designed not to damage surfaces upon impact).
  • Goggles and gloves
Photo of a boat trailer tire

Step 1: Jack the trailer tire on one side high enough so that the tire spins freely and place a jack stand beneath the frame.Chock the opposite trailer wheel. Some will leave the trailer connected to the tow vehicle to ensure there is no movement.

Shake the tire up and down and from side to side. If there is movement, chances are good the bearings are bad.Spin the tire and listen for sounds. In many cases, bad bearings can be heard but be aware this can also be nothing more than brake pads or shoes catching the hub.

Photo of removing the dust cover from your bearing

Step 2: Remove the dust cover or Bearing Buddy with a screwdriver. If the grease is milky, water has entered the bearing assembly. If the grease has different color, it can mean newer grease was added. Wipe all grease away with a rag or towel.

Photo of removing the cotter pin

Step 3: Now remove the cotter pin, castle washer (some trailers have castle-style axle nuts in which case there's no castle washer), axle nut, spindle/axle washer and set aside for safekeeping as you'll be using them again. Shake the tire and the outer bearing should come off. Wipe away bearing grease (look for evidence of metal which points to a bearing or race failure) and inspect for signs of wear including discoloration (a gold color is evidence of heat), and scoring, pitting or dents. If you see any of these, it's time replace, rather than repack the bearings.

Pull the hub off the spindle and lay it with the inner sidewall facing up. Inspect the spindle for any visible damage and then, feel it with your hand. The surface should be smooth.
NOTE: Avoid cleaning bearings and races with gasoline because this can harm the inner seal. paper towels and rags will do the job.

Photo of removing the grease seal

Step 4: Remove the grease seal. Notice the grease on the inner hub in this photo. That's proof the inner seal has failed.

Use channel locks or a seal puller to remove the seal.

Remove the inner bearing and inspect it just as you did with the outer bearing in Step 3.
NOTE: Anytime you remove the inner seal, replace it.

Photo of removing the inner bearing

Step 5: Just like the outer bearing, the inner bearing is seated in a race, also called a bearing cup or a bearing cone. If the bearings are in good condition, remove all the remaining grease in the hub and inspect both the inner and outer races for pitting, scars and/or discoloration.

If everything looks good, all you need to do is repack with fresh grease and a new seal and cotter pin (Go to Step 7). However, if any show signs of wear, it's time to replace everything.
NOTE: If a bearing shows wear but the race looks fine, you still replace both.

Photo of removing the races from a tire hub

Step 6: Getting races out of the hub requires placing a round punch placed against the inside edge of the race and with small taps with a hammer, moving in a circular motion to dislodge it from the hub. The inner race is removed with the outer sidewall facing you and the outer race is removed with the inner sidewall facing you. Some folks use a wooden dowel instead of the round punch. Whatever you choose, wear eye protection.

Place a new race on the hub and with a soft hammer, pound the race all the way in with a circular motion so that its outer edge is flush with the hub. Others position the old race above the new one and pound it in that way. There's even a race insertion tool available at auto parts stores.

You'll know it's in the proper position because it won't go in any further and the sound will change when properly seated.

Photo of greasing the inner hub

Step 7: Grease the inner hub and then pack the inner bearing with grease. Legendary Trailers uses a bearing packer (pictured), which can be found at most auto parts stores for less than $15. Another way is to put grease in the palm of your hand and then place two fingers of your other hand through the larger side of the bearing. Now pack grease into the bearing rollers while rotating the bearing into your palm. You'll do the same with the outer bearing later.

Photo of installing the new and double-lipped grease seal

Step 8: Now install the new and double-lipped grease seal. Double-lipped grease seals have a better chance of keeping water out of the bearing assembly than single-lip seals. It's usually included in bearing kits so be sure to ask or do some research prior to buying. The kits sold at West Marine from CE Smith have double-lip seals. Many prefer using a board across the seal to hammer against thus protecting the seal. You have now completed the inner bearing assembly!

Photo of installing the outer races

Step 9: Turn the wheel over and install the outer race. Then lift the wheel onto the spindle being careful not to poke the grease seal with the spindle's outer edge.

Grease the race and add the outer bearing.

Step 10: Next, add the spindle washer, the axle nut/castle nut tightening until it stops. Bo Adams, vice president of CE Smith (they make bearings for West Marine), says the nut "should be a snug fit" but if too tight, the assembly can be damaged as a result of heat generated when the trailer tires are going down the road. If too loose, the wheel will wobble. Finally, add the castle nut or the castle-style axle washer.

Step 11: Now put a new cotter pin on the assembly turning both ends in the same direction to lock it in place.

Step 12: Add the Bearing Buddy or dust cap and spin the wheel. You shouldn't hear any sound except your own voice saying "Yes!"

Photo of adding spindle washer, cotter pin and Bearing Buddy


This article was published in the July 2010 issue of Trailering Magazine.

 

 Recommended Articles
Gray rule

Thumbnail photo of a trailer braking systemBraking Systems

Once a trailer reaches a certain weight capacity, trailer brakes become a requirement


Thumbnail of a trailer couplerTrailer Couplers, Balls and Jacks

Bent, rusted, or corroded couplers, mounts, and balls, can cause damage and complicate basic trailer hookup

Thumbnail photo of a truck and boat trailerTrailering Tips

Tips on using and maintaining your boat trailer

 

 


Trailering Magazine is a benefit of BoatUS TRAILER ASSIST®.

BoatUS TRAILER ASSIST® provides:

  • On-the-road assistance for your trailer and vehicle
  • Special edition Trailering magazines
  • $15 coupon (off $100 purchase) for shopping at West Marine
  • Only $38 Annually! ($24 Membership + $14 TRAILER ASSIST)

About TRAILER ASSIST