Outboard Water-Pump Impeller Service

Article and Photos by Mark Corke

This is a fairly simple job, and the average do-it-yourselfer most likely has the necessary tools. Here's how it's done.

Ask around at the marina, and chances are that most boat owners have no idea when the water pump on their outboard was last serviced. Some people don't even know that their engines have pumps. The water pump is a critical part of any outboard. A pump that is blocked or working improperly will cause the engine to overheat, which can lead to permanent damage. If you suspect that the outboard is running hot, it could be time to service the water pump. The manual should say how often this should be done, but often every other year is about right. In most cases, this basically consists of replacing the water-pump impeller. Don't try to do this with the boat in the water. Have it hauled if it's large, or do the work when it's on the trailer in the driveway. That way, you won't lose anything vital.

The engine we serviced for this story is a 115-hp, 1996 Mercury. Outboards are very similar and, although the pictures might not look exactly like what you have, the sequence should be the same. You should, however, check the service manual for your own outboard because some are different from the one featured here. I took the pictures as Adam Conte at Portside Marine in Danvers, Massachusetts, serviced the pump.

Unscrewing drain plug with large screwdriver

1. The first step is to drain the oil from the gearbox. Unscrew the drain plug with a large screwdriver, and the oil will start to run out. Place a suitable pan under the engine to catch the old oil. Unscrew the upper oil-level plug, too, which allows air into the gearbox and ensures that all of the oil is evacuated.

Drain gearcase oil

2. There are small washers under each screw head that often get stuck in the threads. If they don't come off with the screw, you may have to pick them out with a small screwdriver or other tool. Let the oil drain as you move on to the next step.

Removing nuts that hold lower unit

3. Loosen and remove the nuts that hold the lower unit in place. Almost every outboard has four nuts holding it. A socket may not fit, so use a ring wrench to give good purchase on the nuts, which probably will be difficult to loosen.

Using rubber mallet to free lower unit

4. Theoretically, the lower unit should now be free; in practice, it invariably sticks and will need a few taps with a soft mallet. Do not hit the flange cavitation plates at the sides or they're sure to break. A few taps on the aft end of the gearbox unit, as shown here, is acceptable. With some outboards, disconnecting the shift rod will require different steps. For example, you may need to unbolt the shift rod connection, then re-bolt it after the job.

Using a screwdriver to pry the lower unit apart

5. Once a crack opens up, the battle is won, and you can carefully insert a broad screwdriver and carefully pry it apart, being very careful not to damage the castings of the mating surfaces. Lift the unit clear and place it on a suitable bench or jig designed for holding it. Portside Marine services outboards every day, so it had a proper jig. That's ideal, but you may have to prop the unit upright in the corner of your garage. It works but is just not as convenient, and you'll be working at floor level.

Sliding off seal atop pump housing

6. With the bottom clear of the top half of the lower unit, you can get to work on the pump. The first thing to do is slide off the seal, which sits atop the pump housing.

Using an impact wrench

7. Unscrew the bolts that hold the pump housing in place. We needed an impact wrench because this pump hadn't been serviced for some time, but a ring wrench will work in most cases. Avoid using an open-ended wrench. If you round over the bolt heads, you'll have a bad day, for sure.

Separate housing and pry-off bottom plate

8. Separate the housing and slide it up the shaft. You can see in this picture that the bottom plate is coming off with it. We need to remove this plate, so if it remains stuck in place you might need to pry it up carefully.

Impellers

9. This pump was in pretty good shape. All of the vanes on the impeller were intact. Note the old impeller on the right, compared to the new one and its straight vanes. The vanes develop a set (or bend) after they've been in the pump for several months.

Cleaning mating surfaces

10. Before reinstalling the pump, clean all of the mating surfaces to ensure that there will be no leaks. A sharp razor blade can be used to scrape off the larger bits of gasket and sealant; some fine emery paper will get rid of the remainder. Wipe with clean rags when you're finished. Everything should be clean and bright.

Cleaning interior pump housing

11. Wipe out the interior of the pump housing, making sure there are no score marks or gouges. If there are, water might leak past the vanes of the impeller and the pump won't work as efficiently as it should. If there is any doubt about the condition of the housing, replace it.

Additional water pump parts

12. In addition to the impeller, all the required parts for routine service — gaskets, O-rings, seals — are included in the water-pump kit.

Smearing on gasket cement

13. After cleaning everything, reassemble with the new parts. Smear on a little gasket cement. Conte, at Portside Marine, swears by Permatex Form-A-Gasket sealant, but other reputable brands should be fine.

Positioning new gasket

14. Lower the gasket into position, making sure that all of the holes line up. The gasket is asymmetrical, so if something looks wrong you may have it upside down.

Installing a new bottom plate

15. Install the new bottom plate that comes in the pump kit. We used a little more gasket sealant before dropping this on.

Installing small gasket that seals joint of pump housing

16. Install the smaller gasket, which seals the joint between the top and bottom sections of the pump housing. This gasket has a neoprene bead built in, so no cement should be used.

Installing a new key on pump shaft

17. Install the new key, which sits in the flat on the shaft.

Installing a new impeller

18. Slide down the new impeller, making sure that the keyway in the hub lines up with the previously fitted key.

Adding glycerin for lubrication

19. A little glycerin or dishwashing liquid makes getting the pump cover on a bit easier and provides lubrication for the second or two before the water gets into the pump and lubricates the vanes. Don't use oil or silicone, which can attack the composition of the impeller and lead to premature failure.

Sliding housing down over vanes

20. Slide the housing down and ease it over the vanes as you twist the shaft in a clockwise direction with the other hand. This bends the blades and allows the body of the pump to sit fully down onto the base plate gasket.

Reinstalling bolts

21. Reinstall the bolts and tighten until they're just snug.

SlidIng new seal down shaft

22. Slide the new seal down over the shaft until it just rests against the pump housing.

Pushing setting tool down on seal

23. Push the setting tool, included in the kit, down on top of the seal, which does the double duty of spreading it out and ensuring that it is not compressed too much. With the seal set, remove the compression tool.

Greasing the drive shaft

24. Smear a little engine spline coupling grease on the top of the drive shaft.

Greasing gear shift coupler

25. Put a little more grease on the gear-shift coupler, which should still be on the gear shift shaft inside the leg. This is a fairly loose push fit, so the coupler may have fallen onto the floor if it isn't where it should be.

Refill gearbox with oil

26. Refill the gearbox with the correct oil. Note that the oil is pumped in from the bottom until it comes out of the upper-level hole. Then both screw plugs can be replaced with a new washer under each. Portside Marine services a lot of engines, so it has a big tub of oil. The average DIYer is more likely to use the oil that comes in squeezable quart bottles, but the technique is the same.

Reinstalling lower unit

27. Reinstall the lower unit. It helps to have someone rotate the engine by hand a little to get the splines to mesh. Replace the nuts and washers that hold the two parts together. There are torque settings for these, but Conte tightens them so they're just snug. As long as you don't swing on the wrench, it is difficult to overtighten these. The service manual may list torque wrench settings, however.

Testing newly serviced engine in a barrel

28. With everything back together, the job is complete. We ran the engine in a barrel to make sure all was well. You can use muffs on the water pickup, but the pressure of the hose tends to force the water into the engine. Running it in a barrel ensures that the suction from the pump is correct. There should be a healthy spout of water coming out of the engine housing. Record the date and engine hours so next time you'll know exactly when the pump is due for servicing. 

— Published: February/March 2017


Tech Support

Degree Of Difficulty
Plus sign symbol Plus sign symbol Plus sign symbol Plus sign symbol Plus sign symbol

Tools and Materials:

  • Water pump kit
  • Gearbox oil
  • Flat-head screwdrivers
  • Oil pan
  • Ring wrench
  • soft mallet
  • Impact wrench
  • Razor blade
  • Emery paper
  • Clean rags
  • Gasket cement/sealant
  • Glycerin or dishwashing liquid
  • Engine spline coupling grease

Time:

This project will take approximately 1 to 2 hours

Cost:

Will vary based on the engine: Ours cost $50

 

BoatUS Magazine Is A Benefit Of BoatUS Membership

Membership Also Provides:

  • Subscription to the print version of BoatUS Magazine
  • 4% back on purchases from West Marine stores or online at WestMarine.com
  • Discounts on fuel, transient slips, repairs and more at over 1,000 businesses
  • Deals on cruises, charters, car rentals, hotel stays and more ...
  • All For Only $24 A Year!

Join Today!