] ]

 
] ] ]
]
Welcome Guest ]
]
] ]

] ] ]
]
Site Navigation ]
]
] ]

] ] ]
]
Top 10 Recent Posts ]
View Last Post Murray Chris Craft Constellations
Pages 1 2 3 4 ... 149 » 150
Last Post By: Capt Jim
Forum: Chris Craft

Posted: August 29 2014 at: 11:06

View Last Post 1991 Four Winns 365
Last Post By: Blue Moon 138
Forum: Four Winns

Posted: July 16 2014 at: 17:35

View Last Post Seat Cushions
Last Post By: Michael Acord
Forum: Sea Fox

Posted: June 06 2014 at: 16:02

View Last Post Sail cleanin’ and hull patchin’
Last Post By: dad21dawg
Forum: Hunter

Posted: May 29 2014 at: 16:01

View Last Post 1983 25’ Chris Craft Catalina
Last Post By: fred6963
Forum: Chris Craft

Posted: May 27 2014 at: 14:26

View Last Post 1963 Constellation 42
Last Post By: spellbound
Forum: Chris Craft

Posted: May 06 2014 at: 08:31

View Last Post Viking Yachts Links
Last Post By: Viking44
Forum: Viking Yacht

Posted: April 17 2014 at: 06:32

View Last Post Amerosport 320
Last Post By: Jerry737
Forum: Chris Craft

Posted: April 13 2014 at: 16:00

View Last Post Any Uniflite Owners near Berkeley CA???
Last Post By: concordian
Forum: Uniflite

Posted: March 08 2014 at: 02:27

View Last Post Inverter
Last Post By: eshover
Forum: Chris Craft

Posted: February 03 2014 at: 11:32

]
] ]
   
Chris Craft
 BoatUS Boat Groups/Manufacturer Forums>>Chris Craft
Subject Topic: Engine Replacement Post ReplyPost New Topic
 
] ] ]
]
Author
Message Prev Topic | Next Topic 
Banjoman
"First Mate"




Joined: July 02 2007
Posts: 553
Posted: September 03 2007 at 23:26 | IP Logged Quote Banjoman

Hi folks,

1)Would like any first-hand information regarding replacement of the engines in a flush-deck MY (such as the 460/500 or a similar Uniflight).  And no, I'm not talking about in-frame rebuilding.  I mean bench built DD's and installed without tearing the engines down (again) just to get them in.  It has been suggested the cabin roof be cut in panels  (port and starboard) and the old engines be removed and new engines installed, then the panels are re-glassed.  Sounds reasonable, if not expensive.  However, the time it takes to tear down the old engines for removal AND new engines for install wouldn't be very cheap either, not to mention the cost of any damage done getting the (very heavy) heads, manifolds, short block, etc. out through the cabin space.

2) Has anyone had a "fuel starvation" issue?  Low RPM @ full load?  I'm only getting 1950 rpm at full load! Can the old fuel lines cause this?  My fuel lines are original (1986) and I've had to replace a couple of them at the valve manifold.  I had to do a lot of work on the port engine over the last 3 years and, yes, I've stood on the fuel line on more than one occasion.  Of course, my low rpm doesn't seem to change whether on the forward OR aft tanks.  Plenty of soot on transom too.  For some reason, the exhaust note on the port engine even sounds different also.  Got any ideas?

If anyone has had any experience in this area, I'd love to hear from you.

Capt. G. Emory Shover - Eastern Marine Services,  LLC

m/v Southern Charm - Mill Creek, Md



__________________
Capt. G. Emory Shover
m/v "SOUTHERN CHARM"
Eastern Marine Services, LLC
Marine Survey - Yacht Delivery
www.easternmarineservices.com
Back to Top Printable version View Banjoman's Profile Search for other posts by Banjoman
 
]
] ]
 

If you wish to post a reply to this topic you must first login
If you are not already registered you must first register

  Post ReplyPost New Topic

] ] ]
]
  ]
Printable version Printable version
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum
]
] ]

] ] ]
]
©2014, Boat Owners Association of The United States. All Rights Reserved.
This page was generated in 1.4060 seconds.
]
] ]