] ]

 
] ] ]
]
Welcome Guest ]
]
] ]

] ] ]
]
Site Navigation ]
]
] ]

] ] ]
]
Top 10 Recent Posts ]
View Last Post Mainship 30 Pilot Canvas for Sale
Last Post By: Geraldine
Forum: Mainship

Posted: Yesterday at: 21:52

View Last Post Murray Chris Craft Constellations
Pages 1 2 3 4 ... 134 » 135
Last Post By: DMark
Forum: Chris Craft

Posted: May 17 2013 at: 16:33

View Last Post Maxum Links
Last Post By: RNR-Marine
Forum: Maxum

Posted: April 24 2013 at: 08:39

View Last Post Mariah links
Last Post By: RNR-Marine
Forum: Mariah

Posted: April 23 2013 at: 12:12

View Last Post Silvertons on the Chesapeake
Last Post By: BluesBarge
Forum: Silverton

Posted: April 22 2013 at: 18:01

View Last Post Sea Fox Links
Last Post By: RNR-Marine
Forum: Sea Fox

Posted: April 22 2013 at: 11:27

View Last Post Sea Hunt Links
Last Post By: RNR-Marine
Forum: Sea Hunt Boats

Posted: April 22 2013 at: 11:11

View Last Post Sea Boss Links
Last Post By: RNR-Marine
Forum: Sea Boss

Posted: April 22 2013 at: 11:02

View Last Post Sea Pro Links
Last Post By: RNR-Marine
Forum: Sea-Pro

Posted: April 22 2013 at: 11:00

View Last Post Searching Harbor Master owners
Last Post By: steve1234
Forum: Harbor Master

Posted: March 30 2013 at: 21:13

]
] ]
   
Bayliner
 BoatUS Boat Groups/Manufacturer Forums>>Bayliner
Subject Topic: Problems Post ReplyPost New Topic
 
] ] ]
]
Author
Message Prev Topic | Next Topic 
wusit2ya
"Seaman Recruit"




Joined: July 31 2007
Posts: 2
Posted: July 31 2007 at 14:32 | IP Logged Quote wusit2ya

1991 Bayliner capri with 3.0 Mercruiser, problem is boat runs great full throttle and when you bring it back down to an idle  it drops down to 600 rpm for 2 to3 minutes and then will idle out smooth around 900. Does this every time i run it and some times dies and have to restart.

Any ideas


Back to Top Printable version View wusit2ya's Profile Search for other posts by wusit2ya
 
barneybutler
"Seaman Recruit"




Joined: August 13 2007
Posts: 5
Posted: August 13 2007 at 15:41 | IP Logged Quote barneybutler

adjust idle mixture screw.
with engine warmed up and running turn the mixture screws [one at a time if you have two vinturie carb] in until the engine runs rough then unscrew until it is smooth again,  then 1/4 turn out more.  Then do the other screw.
If this doesn't work you might have a too high float level in the carb.
get the float level setting from a book or supplier and adjust it.  or if you are feeling adventurous remove the top of the carb and turn it upside down on a bench.
use a ruler and measure from the metal underside of air horn [top of carb] to a place on the float [it can be the bottom or the float or top or a line seam and make note of that measurement.  now bend the tang that pushes on the float needle toward the needle to lower the fuel level in the bowl or bend it away from the needle to increse the fuel level.  I would lower it by about 1/8 to1/16" at the float where you measured it before.  If this doesn't work I would need more info to help more.

Good luck
Barney
barneybutler@hotmail.com


__________________
Barney
Back to Top Printable version View barneybutler's Profile Search for other posts by barneybutler
 
wusit2ya
"Seaman Recruit"




Joined: July 31 2007
Posts: 2
Posted: August 14 2007 at 13:19 | IP Logged Quote wusit2ya

Problem fixed

Pulled the carb. off and took apart only to find a ton of sediment in the bottom of float bowl. Cleaned carb and installed new carb. kit and a secondary fuel filter. Runs like a champ now and back to idleing at 650.

Thanks for all the ideas !
Back to Top Printable version View wusit2ya's Profile Search for other posts by wusit2ya
 
barneybutler
"Seaman Recruit"




Joined: August 13 2007
Posts: 5
Posted: August 14 2007 at 22:41 | IP Logged Quote barneybutler

great, your welcome.
Barney


__________________
Barney
Back to Top Printable version View barneybutler's Profile Search for other posts by barneybutler
 
]
] ]
 

If you wish to post a reply to this topic you must first login
If you are not already registered you must first register

  Post ReplyPost New Topic

] ] ]
]
  ]
Printable version Printable version
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum
]
] ]

] ] ]
]
©2013, Boat Owners Association of The United States. All Rights Reserved.
This page was generated in 0.9375 seconds.
Powered by SOOP Portal version Raven RC1
]
] ]